欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136

標題: 23LC1024 SRAM 綜合測試（BASCOM-AVR版） [打印本頁]

作者: taotie 時間: 2025-10-7 11:03
標題: 23LC1024 SRAM 綜合測試（BASCOM-AVR版）

程序：
rem Main.bas file generated by New Project wizard
rem
rem Created: 周日 10月 5 2025
rem Processor: ATmega16
rem Compiler:  BASCOM-AVR

rem 23LC1024 SRAM 綜合測試（BASCOM-AVR版）

$regfile = "m16def.dat"
$crystal = 8000000
$hwstack = 64
$swstack = 64
$framesize = 64

' 引腳定義
'如果不配置Noss = 1就不能使用硬件spi的ss管腳Portb.2！！！！這時須選擇其他端口管腳單獨配置如PortD.2。
'或者加實物上拉電阻可取消Portb.2 = 1
'Config PinD.2 = Output
'PortD.2 = 1
Cs Alias Portb.4

' SPI 配置
Config Spi = Hard , Interrupt = Off , Data Order = Msb , Master = Yes , Polarity = Low , Phase = 0 , Noss = 1
Spiinit

' 變量定義
Dim Write_byte As Byte , Read_byte As Byte
Dim Temp As Byte
Dim i As Byte , j As Byte
Dim Test_data As Byte
Dim Addr As Long
Dim Error_count As Word
Dim Addr_high As Byte
Dim Addr_mid As Byte
Dim Addr_low As Byte
Dim Pass_count As Word

' 串口配置
'Config Com1 = 9600 , Parity = None , Stopbits = 1 , Databits = 8
$baud = 9600
' 聲明子程序
Declare Sub Spi_write()
Declare Sub Spi_read()
Declare Sub Test_single_address()
Declare Sub Test_multiple_addresses()
Declare Sub Test_sequential_addresses()
Declare Sub Test_boundary_addresses()
Declare Sub Test_data_patterns()

' 主程序
Print
Print " ========================================"
Print "       23LC1024 SRAM 綜合測試"
Print " ========================================"
Print

Waitms 1000

' 運行各種測試
Call Test_single_address
Call Test_multiple_addresses
Call Test_sequential_addresses
Call Test_boundary_addresses
Call Test_data_patterns

Print
Print " ========================================"
Print " 所有測試已完成！"
Print " ========================================"

Do
' 主循環
Loop
End

' SPIWrite子程序
Sub Spi_write()
Addr_high = Addr / 65536
Addr_mid = Addr / 256
Addr_low = Addr And &HFF

Reset Cs
Temp = &H02 : Spiout Temp , 1                   ' WRITE命令
Spiout Addr_high , 1                            ' 地址高字節
Spiout Addr_mid , 1                            ' 地址中字節
Spiout Addr_low , 1                            ' 地址低字節
Spiout Write_byte , 1                         ' 數據
Set Cs
Waitms 5                                        ' Write周期等待
End Sub

' SPI讀子程序
Sub Spi_read()
Addr_high = Addr / 65536
Addr_mid = Addr / 256
Addr_low = Addr And &HFF

Reset Cs
Temp = &H03 : Spiout Temp , 1                   ' READ命令
Spiout Addr_high , 1                            ' 地址高字節
Spiout Addr_mid , 1                            ' 地址中字節
Spiout Addr_low , 1                            ' 地址低字節
Spiin Read_byte , 1                            ' 讀取數據
Set Cs
End Sub

' 測試1: 單地址基本功能
Sub Test_single_address()
Print " 測試 1：單地址基本功能"
Print " ----------------------------------------"

Addr = &H1234
Write_byte = &HA5

Call Spi_write
Call Spi_read

Print " Address: 0x" ; Hex(addr) ; "  Write: 0x" ; Hex(write_byte) ; "  Read: 0x" ; Hex(read_byte)

If Write_byte = Read_byte Then
   Print " >>> 單地址測試：通過"
Else
   Print " >>> 單一地址測試：失敗"
End If
Print
End Sub

' 測試2: 多地址測試
Sub Test_multiple_addresses()
Print " 測試 2：多地址測試"
Print "----------------------------------------"

Error_count = 0

For i = 1 To 10
   Addr = i * &H1000                         ' 遞增地址
   Write_byte = i * &H11                      ' 遞增數據

   Call Spi_write
   Call Spi_read

   Print " Addr: 0x" ; Hex(addr) ; "  Write: 0x" ; Hex(write_byte) ; "  Read: 0x" ; Hex(read_byte)

   If Write_byte <> Read_byte Then
      Incr Error_count
      Print " *** 地址 0x 處出錯" ; Hex(addr)
   End If
Next i

Pass_count = 10 - Error_count
Print " 多個地址測試： " ;Pass_count ;"/10 通過"
Print
End Sub

' 測試3: 連續地址測試
Sub Test_sequential_addresses()
Print " 測試 3：連續地址測試"
Print " ----------------------------------------"

Error_count = 0
Addr = &H5000

For i = 0 To 15
   Write_byte = &H40 + i                      ' 連續數據

   Call Spi_write
   Call Spi_read

   If Write_byte <> Read_byte Then
      Incr Error_count
      Print " *** 在順序地址處出現錯誤 " ; i
   End If
   Addr = Addr + 1
Print  " Addr: 0x" ; Hex(addr) ;"Write 0x" ; Hex(write_byte);" Read 0x" ;Hex(read_byte)
Next i

Pass_count = 16 - Error_count
Print" 連續地址測試: " ;Pass_count ;"/16 通過"
Print
End Sub

' 測試4: 邊界地址測試
Sub Test_boundary_addresses()
Print " 測試 4：邊界地址測試"
Print " ----------------------------------------"

Error_count = 0

' 測試邊界地址
Write_byte = &H5A

' 最低地址
Addr = &H00000
Call Spi_write
Call Spi_read
Print " 邊界 0x" ; Hex(addr) ; " : Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count

' 第一頁結束
Addr = &H000FF
Call Spi_write
Call Spi_read
Print " 邊界 0x" ; Hex(addr) ; " : Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count

' 最后頁開始
Addr = &H1FF00
Call Spi_write
Call Spi_read
Print " 邊界 0x" ; Hex(addr) ; " : Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count

' 最高地址 (128KB)
Addr = &H1FFFF
Call Spi_write
Call Spi_read
Print " 邊界 0x" ; Hex(addr) ; " : Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count

Pass_count = 4 - Error_count
Print " 邊界地址測試: " ;Pass_count ;"/4 通過"
Print
End Sub

' 測試5: 數據模式測試
Sub Test_data_patterns()
Print " 測試 5：數據模式測試"
Print "----------------------------------------"

Error_count = 0
Addr = &H8000

' 測試各種數據模式
Write_byte = &H00                            ' 全0
Call Spi_write : Call Spi_read
Print " 模式 1：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &HFF                            ' 全1
Call Spi_write : Call Spi_read
Print " 模式 2：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &H55                            ' 01010101
Call Spi_write : Call Spi_read
Print " 模式 3：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &HAA                            ' 10101010
Call Spi_write : Call Spi_read
Print " 模式 4：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &H0F                            ' 00001111
Call Spi_write : Call Spi_read
Print " 模式 5：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &HF0                            ' 11110000
Call Spi_write : Call Spi_read
Print " 模式 6：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &H33                            ' 00110011
Call Spi_write : Call Spi_read
Print " 模式 7：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count
Addr = Addr + 1

Write_byte = &HCC                            ' 11001100
Call Spi_write : Call Spi_read
Print " 模式 8：Write 0x" ; Hex(write_byte) ; " Read 0x" ; Hex(read_byte)
If Write_byte <> Read_byte Then Incr Error_count

Pass_count = 8 - Error_count
Print " 數據模式測試： " ;Pass_count ;"/8 通過"
Print
End Sub

歡迎光臨 (http://m.raoushi.com/bbs/)