亚洲精品国产第一区第二区国,亚洲精品久久国产一区,久久久久国产极品

#include <stc8h.h>
#include <intrins.h>
#define FOSC 22118400L
#define BAUD 38400
#define uint unsigned int
#define uchar unsigned char
//HUB75引腳
sbit R0 = P0^0; sbit G0 = P1^0;
sbit B0 = P0^1; //接地
sbit R1 = P0^2; sbit G1 = P1^1;
sbit B1 = P0^3; sbit HC_138E = P1^2;
sbit HC_138A = P0^4; sbit HC_138B = P1^6;
sbit HC_138C = P0^5; sbit HC_138D = P1^7;
sbit RGB_CLK = P0^6; sbit LE = P2^0;//LAT
sbit OE = P0^7; //接地
void DZ64X32_Write_Buffer();
void SM16126_Send_Data();
void HC138_Sel(uchar hang);
void LED_Tu(uchar x,uchar y,uchar num,uchar Background);
uchar code Tu_16X16[][32]; //***********************************
#define T10MS12T (65536-FOSC/12/3000)//967 //原值1000，畫面閃動，改成3000就穩定了
#define T1MS12T (65536-FOSC/12/1000) //************************************
void Timer1_Init()//主刷新定時器
{
TL0 = T10MS12T;
TH0 = T10MS12T>>8;
TR0 = 1;
ET0 = 1;
}
void TM1_Rountine(void) interrupt 1
{
SM16126_Send_Data();
}
void HC138_Sel(uchar hang)//hang 選擇
{
HC_138A=hang&0x01;
HC_138B=hang&0x02;
HC_138C=hang&0x04;
HC_138D=hang&0x08;//***********************************
HC_138E=hang&0x10;//改成32掃
} //******************************************
//數據存儲方式，因為漢字需要左右滾動，所以上下兩16行存儲在同一Byte
#define C_0 0
#define C_R 0x09
#define C_G 0x0A
#define C_B 0x0C
#define C_RG 0x0B
#define C_RB 0x0D
#define C_GB 0x0E
#define C_RGB 0x0F
uchar bdata dat;
/*
0 1 2 3 4 5 6 7
R G B L R G B H
L存儲是否點亮，R,G,B存儲值
一個點需要4bit，一共是32*64*4=32*32Byte
*/
sbit dat_RL=dat^0;
sbit dat_GL=dat^1;
sbit dat_BL=dat^2;
sbit dat_LL=dat^3;
sbit dat_RH=dat^4;
sbit dat_GH=dat^5;
sbit dat_BH=dat^6;
sbit dat_LH=dat^7;
uchar Point_color;//取值范圍0，9-15,同時//********************************************************
uchar xdata RGB_DZ64X32_Buffer[32][128];//原值為32和64；點亮64x128點陣屏
//顯示分左右兩相同內容，右邊內容上移壹行。如圖1.
void DZ64X32_Write_Buffer() //改成32和128時，第2和第4排的上部8行顯示正常，
{ //下8行位置被條紋覆蓋，如圖2.
uchar i,j; //*******************************************************
for(i=0;i<32;i++)
{
for(j=0;j<128;j++)
{
RGB_DZ64X32_Buffer[i][j]=0x00;
}
}
}
void SM16126_Send_Data()
{
uchar i;
static uchar hang;
RGB_CLK=0;//低電平
LE=1;//允許數據，
OE=1;//失效，不亮
//****************************************
for(i=0;i<128;i++) //64列是原值，改成128列
{ //****************************************
dat=RGB_DZ64X32_Buffer[hang][i];//取出數據
RGB_CLK=0;
//---上半屏
if(dat_LL)//有數據
{
R0=dat_RL;
G0=dat_GL;
B0=dat_BL;
}
else//沒有數據
{
R0=0;
G0=0;
B0=0;
}
//---下半屏
if(dat_LH)//有數據
{
R1=dat_RH;
G1=dat_GH;
B1=dat_BH;
}
else//沒有數據
{
R1=0;
G1=0;
B1=0;
}
RGB_CLK=1;//上升沿數據吸收
}
LE=0;//禁止輸入
HC138_Sel(hang);//行選
hang++; //*************************************
hang&=0x1f; //原值是0x0f，0~15 16行；改成0x1f，0~31 32行
OE=0;//點亮 //***************************************
}
void DZRGB_DrawPoint(uchar x,uchar y)
{
uchar da,db;
if(Point_color)//有亮度
{
if(y>=32)//在高位 //************************************
{ //原值16，改成32
y-=32; //**************************************
da=Point_color<<=4;//移動到高位
db=RGB_DZ64X32_Buffer[y][x];//取出數據
db&=0X0F;//清除高位00001111
RGB_DZ64X32_Buffer[y][x]=db+da;
}
else//在低位
{
db=RGB_DZ64X32_Buffer[y][x];//取出數據
db&=0XF0;//清除低位 11110000
RGB_DZ64X32_Buffer[y][x]=db+Point_color;
}
}
else//沒有亮度
{
if(y>=32)//在高位
{
y-=32;
RGB_DZ64X32_Buffer[y][x]&=0x7F;//01111111
}
else
{
RGB_DZ64X32_Buffer[y][x]&=0xE7;//11100111
}
}
}
uchar code er[8]={1,2,4,8,16,32,64,128};
void LED_Tu(uchar x,uchar y,uchar num,uchar Background)
{
uchar i,j;
uchar Point_color_Save;
Point_color_Save=Point_color;//保存顏色
for(j=0;j<16;j++)//16列
{
for(i=0;i<8;i++)//前8行
{
if(Tu_16X16[num][j]&er[i])
{
Point_color=Point_color_Save;
}
else
{
Point_color=Background;
}
DZRGB_DrawPoint(x+j,y+i);
}
}
for(j=0;j<16;j++)//16列
{
for(i=0;i<8;i++)//后8行
{
if(Tu_16X16[num][j+16]&er[i])
{
Point_color=Point_color_Save;
}
else
{
Point_color=Background;
}
DZRGB_DrawPoint(x+j,y+8+i);
}
}
Point_color=Point_color_Save;
}
void main()
{
P2M0=0x00;P2M1=0X00;
P1M0=0X00;P1M1=0X00;
P0M0=0X00;P0M1=0X00;
//*******************************************
Timer1_Init(); //主程序只運行Timer1_Init();DZ64X32_Write_Buffer(); .
DZ64X32_Write_Buffer(); //點陣屏第2和第4組下8行出現條紋，如圖3
//*******************************************
// Point_color=C_R;
// LED_Tu(0,0,1,C_0);LED_Tu(48,0,5,C_0);
// LED_Tu(0,16,2,C_0);LED_Tu(48,16,10,C_0);
// Point_color=C_G;
// LED_Tu(0,32,3,C_0);LED_Tu(48,32,7,C_0);
// LED_Tu(0,48,4,C_0);LED_Tu(48,48,8,C_0);
EA=1; //打開總中斷
while(1)
{
}
}
uchar code Tu_16X16[][32]={ //陰碼順向行列掃描
0x10,0x0C,0x05,0x55,0x55,0x55,0x85,0x7F,0x85,0x55,0x55,0x55,0x05,0x14,0x0C,0x00,
0x04,0x04,0x02,0x0A,0x09,0x29,0x2A,0x4C,0x48,0xA9,0x19,0x02,0x02,0x04,0x04,0x00, //"零",0
0x00,0xC4,0x44,0x54,0x54,0x54,0x54,0x5F,0x54,0x54,0x54,0x54,0x44,0x44,0xC0,0x00,
0x81,0x80,0x80,0x9D,0xB5,0xD5,0x95,0x95,0x95,0xD5,0xB5,0x9D,0x80,0x81,0x80,0x00, //"壹",1
0x04,0x44,0x54,0x54,0x54,0x54,0x54,0x54,0x54,0x04,0xFF,0x04,0x05,0x06,0x04,0x00,
0x00,0x80,0x9F,0x41,0x21,0x1D,0x21,0x41,0x9F,0x00,0x01,0x0E,0x30,0x40,0xF0,0x00, //"貳",2
0x00,0x20,0x20,0xA8,0x6C,0x2A,0x39,0x28,0x28,0x2A,0x6C,0xA8,0x20,0x20,0x00,0x00,
0x02,0x02,0x41,0x40,0x48,0x49,0x49,0x49,0x49,0x49,0x48,0x40,0x41,0x02,0x02,0x00, //"叁",3
0x00,0x00,0xFE,0x92,0x92,0x92,0x02,0x10,0x54,0x54,0xFF,0x54,0x54,0x7C,0x10,0x00,
0x44,0xE4,0x5F,0x44,0x44,0x54,0xE4,0x12,0x12,0x12,0xFF,0x12,0x12,0x12,0x10,0x00, //"肆",4
0x00,0x80,0x60,0xF8,0x07,0x00,0x42,0x42,0xC2,0x7E,0x42,0x42,0xC2,0x02,0x00,0x00,
0x01,0x00,0x00,0xFF,0x00,0x40,0x40,0x78,0x47,0x40,0x40,0x40,0x7F,0x40,0x40,0x00, //"伍",5
0x00,0xFE,0x02,0x22,0xDA,0x06,0x80,0x88,0x88,0x88,0xFF,0x88,0x88,0x88,0x80,0x00,
0x00,0xFF,0x08,0x10,0x08,0x07,0x00,0x7C,0x40,0x40,0x7F,0x40,0x40,0xFC,0x00,0x00, //"陸",6
0x00,0x88,0x91,0x42,0x20,0x08,0x08,0x08,0x7F,0x88,0x88,0x84,0x84,0xE4,0x00,0x00,
0x44,0x44,0x25,0x24,0x14,0x0C,0x04,0xFF,0x04,0x0C,0x14,0x24,0x24,0x44,0x44,0x00, //"柒",7
0x10,0x10,0xFF,0x10,0x90,0x3E,0xE2,0x22,0x22,0x3E,0x00,0xF8,0x00,0xFF,0x00,0x00,
0x42,0x82,0x7F,0x81,0x40,0x31,0x0F,0x41,0x81,0x7F,0x00,0x4F,0x80,0x7F,0x00,0x00, //"捌",8
0x04,0x44,0x44,0xFC,0x44,0x44,0x80,0x70,0x0F,0x08,0x08,0xC8,0x38,0x00,0x00,0x00,
0x10,0x30,0x10,0x0F,0x08,0x88,0x40,0x20,0x10,0x0C,0x03,0x0C,0x30,0x40,0x80,0x00, //"玖",9
0x10,0x10,0x10,0xFF,0x10,0x90,0x20,0x50,0x48,0x44,0x43,0x44,0x48,0x50,0x20,0x00,
0x04,0x44,0x82,0x7F,0x01,0x00,0x00,0xFE,0x42,0x42,0x42,0x42,0x42,0xFE,0x00,0x00, //"拾",10
};

復制代碼

欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136