欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136

標題: 基于arduino的溫濕度采集及oled顯示屏實時顯示實驗 [打印本頁]

作者: 15034148562 時間: 2020-2-28 11:55
標題: 基于arduino的溫濕度采集及oled顯示屏實時顯示實驗
最近用arduino做了一個小實驗，通過溫度和濕度傳感器采集當前室內溫度和濕度，并在溫度和濕度超標的時候發出報警，同時將溫濕度數據實時oled顯示，也可以通過串口觀測數據，話不多說，代碼如下：

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <dht.h>
dht DHT;
#include <MsTimer2.h>
#include <SPI.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#define ONE_WIRE_BUS 7
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature sensors(&oneWire);
#define uint8  unsigned char
#define uint16 unsigned int
#define OLED_RESET 8
Adafruit_SSD1306 display(OLED_RESET);
#define uint8  unsigned char
#define uint16 unsigned int
#include <MsTimer2.h>
#define OLED_RESET 8
const int DHT11_PIN= 8;//Humiture sensor attach to pin7
int buzzerPin = 6;

int incomingByte = 0;                   // 接收到的 data byte
String inputString = "";                // 用來儲存接收到的內容
boolean newLineReceived = false;       // 前一次數據結束標志
boolean startBit  = false;             //協議開始標志

String returntemp = "";          //存儲返回值
char temp[100] = {0};

void setup() {
  // put your setup code here, to run once:
Serial.begin(9600);
sensors.begin(); // initialize the bus
display.begin(SSD1306_SWITCHCAPVCC, 0x3c);  // initialize with the I2C addr 0x3D (for the 128x64)
display.clearDisplay();
pinMode(buzzerPin,OUTPUT);//set the buzzer as as OUTPUT
// digitalWrite(buzzerPin,LOW);//initialize the buzzerPin as LOW level
digitalWrite(buzzerPin,HIGH);
}

void loop() {
while(1){
display.setTextSize(2);
display.setTextColor(WHITE);
display.setCursor(0,0);
display.println("deg:");
display.setCursor(110,0);
display.println("C");
display.setCursor(0,30);
display.println("wet:");
display.display();
gettempture();
dht();
display.setTextSize(2);
display.setTextColor(WHITE);
display.setCursor(0,0);
display.println("deg:");
display.setCursor(110,0);
display.println("C");
display.setCursor(0,30);
display.println("wet:");
display.display();
//int chk = DHT11.read(8);          //讀取溫濕度傳感器管腳的數值
//int fTemp = (float)DHT11.temperature;       //fTemp賦值為浮點型讀取到的溫度值
//int  iHumidity = DHT11.humidity;          //iHumidity賦值為讀取到的濕度值
memset(temp, 0x00, sizeof(temp));       //清空temp數組
dtostrf(gettempture(), 3, 1, temp);  // 相當於 %3.2f
String sTemp = temp;       //數組temp中的字符串賦給sTemp
String sHum =  "";
sHum += dht();
returntemp = "$TH-T" + sTemp + "-H" + sHum + "#";
Serial.print(returntemp); //返回協議數據包
inputString = ""; // clear the string
// delay(3000);
}
}
float gettempture(void) {
float temp1=0;
float realtemp=0;
  display.clearDisplay();
  display.setTextSize(2);
  display.setTextColor(WHITE);
  display.setCursor(50,0);
  for(int a=0;a<2;a++){
sensors.requestTemperatures();
temp1=sensors.getTempCByIndex(0);
realtemp+=temp1;

  }
realtemp=realtemp/2;
display.println(realtemp);
display.display();

if(realtemp>30)
{
digitalWrite(buzzerPin,LOW);
}
else
{
digitalWrite(buzzerPin,HIGH);
}
return realtemp;

}
float dht(void)
{
  D: int chk = DHT.read11(DHT11_PIN);//read the value returned from sensor
  switch (chk)
  {
  case DHTLIB_OK:
//Serial.println("OK!");
break;
  case DHTLIB_ERROR_CHECKSUM:
//goto D;
//Serial.print("Checksum error,\t");
break;
  case DHTLIB_ERROR_TIMEOUT:
   goto D;
//Serial.print("Time out error,\t");
break;
  default:
   // goto D;
//Serial.print("Unknown error,\t");
break;
  }
  display.setTextSize(2);
  display.setTextColor(WHITE);
  display.setCursor(50,30);
  display.println(DHT.humidity,1);
  display.display();

  if(DHT.humidity>50)
{
digitalWrite(buzzerPin,LOW);
}
else
{
digitalWrite(buzzerPin,HIGH);
}
return DHT.humidity;
}

歡迎光臨 (http://m.raoushi.com/bbs/)