欧美极品高清xxxxhd,国产日产欧美最新,无码AV国产东京热AV无码,国产精品人与动性XXX,国产传媒亚洲综合一区二区,四库影院永久国产精品,毛片免费免费高清视频,福利所导航夜趣136

標題: 時間繼電器倒計時控制定時通斷開關模塊程序包帶原理圖 [打印本頁]

作者: zhangxinchun 時間: 2019-11-17 22:12
標題: 時間繼電器倒計時控制定時通斷開關模塊程序包帶原理圖
#include <reg52.h>    //用52的頭文件  里面加的引腳再定義
#include "intrins.h" //延時
sfr AUXR = 0x8e;
sfr P5 = 0xc8;    //p5定義  是加的
sfr P5M0 = 0xc9;
sfr P5M1 = 0XCA;
sfr P3M0 = 0xb2; //p3口設置強推完的定義
sfr P3M1 = 0Xb1;
sfr P1M0 = 0x92; //p0口設置強推完的定義    這樣設置數碼管就亮
sfr P1M1 = 0X91;
/***********************掉電存儲開始********************/
typedef unsigned char BYTE;
typedef unsigned int WORD;    //類型定義
unsigned char x = 0;
sfr  IAP_DATA    = 0xC2;          //IAP數據寄存器
sfr  IAP_ADDRH = 0xC3;          //IAP地址寄存器高字節
sfr  IAP_ADDRL = 0xC4;          //IAP地址寄存器低字節
sfr  IAP_CMD    = 0xC5;          //IAP命令寄存器
sfr  IAP_TRIG    = 0xC6;          //IAP命令觸發寄存器
sfr  IAP_CONTR = 0xC7;          //IAP控制寄存器
#define CMD_IDLE    0             //空閑模式
#define CMD_READ    1             //IAP字節讀命令
#define CMD_PROGRAM  2                //IAP字節編程命令
#define CMD_ERASE 3                //IAP扇區擦除命令
#define ENABLE_IAP 0x82          //if SYSCLK<20MHz
#define IAP_ADDRESS  0x0400    //測試地址
//void Delay(BYTE n);
void IapIdle();
BYTE IapReadByte(WORD addr);
void IapProgramByte(WORD addr, BYTE dat);
void IapEraseSector(WORD addr);
/***********************掉電存儲結束****************/
/*****************************數碼管開始***********************************/
unsigned int i = 0;//用于掃描數碼管
unsigned char bainum1 = 0;//百
unsigned char shinum1 = 0;//十
unsigned char genum1 = 0;//個
sbit pa = P1^0;sbit pb = P3^2;sbit pc = P3^7;sbit pd = P1^3;//數碼管段
sbit pe = P1^2;sbit pf = P1^4;sbit pg = P3^3;//數碼管段
sbit p1 = P1^1;sbit p2 = P3^6;sbit p3 = P5^5;//數碼管位
void s0();void s1();void s2();void s3();void s4();void s5();//數碼管部分
void s6();void s7();void s8();void s9();void s10();//數碼管部分
void xuaze(unsigned char j);//數碼管段顯示
void displaynum(unsigned int);//顯示函數
//unsigned char code duan [] ={0,1,2,3,4,5,6,7,8,9};
unsigned int bainum11=0,shinum11=0,genum11=0;//用于傳到數碼管上顯示
/*****************************數碼管結束***********************************/
unsigned int inum1=0,inum2=0;//觸發端子用的計數
unsigned char inum11=0,inum12=0,inum21=0,inum22=0,ss=0;//掉電存儲要用到
static unsigned char presstime=0;//時間值按鍵用到的
unsigned int kf0=1;//按鍵用的標志位
unsigned int kt0=0;//按鍵用的標志位
unsigned int  if0=1,if0s=1,it0=0;
unsigned int  mm=0,ff=0,sss=0;//計數用
bit flag_eeprom1=1;//掉電存儲的標志位
unsigned int keynum=0;//數碼管的位
sbit key2=P3^0;//按鍵
sbit key1=P3^1;//按鍵
sbit out= P5^4;//輸出
void timer0_1init();//定時器聲明
void keycan();//按鍵
void keyflag();//按鍵結束調用
void saveeepro();//掉電存儲
extern void displaynums();//將數字傳到數碼管上顯示
void main()
{
timer0_1init();
   P3M0 = 0xcc;
   P3M1 = 0X00;    //p3口設置強推挽
   P1M0 = 0x1f;
   P1M1 = 0X00;
inum11 = IapReadByte(1);//讀取掉電存儲里的值
inum12 = IapReadByte(2);
inum21 = IapReadByte(3);
inum22 = IapReadByte(4);
if0 = IapReadByte(5);
if0s = IapReadByte(6);
ss    = IapReadByte(7);
   inum1=inum11*100+inum12;//組合掉電存儲中的值
   inum2=inum21*100+inum22;
bainum11=inum1/100;//傳到數碼管顯示
shinum11=inum1/10%10;
genum11=inum1%10;
while(1){
keycan();//按鍵
}
}
void keycan(){//按鍵
if(keynum==0){//當按鍵值等于0的時候調用顯示
displaynums();//數碼管的顯示
if(if0s==0){//當if0s等于0時，繼電器輸出
out=0;
}
if((flag_eeprom1==1)){//加掉電存儲
saveeepro();//掉電存儲
flag_eeprom1=0;
}
}
if(key1==0){//當按鍵1按下
if(kf0){//當標志位kf0=1的時候進行
if(presstime>50){//當時間值大于一百的時候
kf0=0;//標志位kf0=0
kt0=1;//標志位kt0=0
flag_eeprom1=1;if0s=1;out=1;if0=1;
presstime=0;//時間清零，重新進行
keynum++;//數碼管的位
         if(keynum==4){//當位到4則置位0
   keynum=0;
   if0=0;
   }
if(out==0){
if0=0;
}

}
    }
}else{//當按鍵松開
keyflag();
if((flag_eeprom1==1)){ //加掉電存儲，必需加到這，不然有一些小問題
flag_eeprom1=0;
saveeepro();//掉電存儲
}
}//按鍵1結束
if(key2==0){if(kf0){if(presstime>50){kf0=0;kt0=1;presstime=0;flag_eeprom1=1;//掉電存儲的標志位改為1，進行存值操作
// if(out==0){
// if0=0;if0s=1;out=1;
// }
switch(keynum){
case 1:
bainum11++;//數碼管一加加
if(bainum11>9){//當數碼管一加加到9時置為1
bainum11=0;
}
break;
case 2:shinum11++;if(shinum11>9){shinum11=0;}break;
case 3:genum11++;if(genum11>9){genum11=0;}break;
default:break;
}
}}}else{keyflag();displaynums();
if((flag_eeprom1==1))//加掉電存儲，必需加到這，不然有一些小問題
{ flag_eeprom1=0;
        saveeepro();//掉電存儲
}
}//松開按鍵進行顯示
}

void tm0_isr() interrupt 1 using 1
{//500等1s
TL0 = 0x18; //設置定時初值
TH0 = 0xFC; //設置定時初值
presstime++;
i++;
   if (if0==0){//當if0==0時開始倒計時
mm++;
if(mm==500){//一秒時間到
mm=0;
ff++;
if(ff>60){//一分鐘
ff=0;
sss++;
ss=sss;
flag_eeprom1=1;
if(sss>60){//一小時
sss=0;
inum2--;
flag_eeprom1=1;
if(inum2==0){
if0s=0;//繼電器輸出
if0=1;//返回設置的時長
flag_eeprom1=1;
}
}
}
}
}
   switch (i){
      case 1: s10(); xuaze(bainum1); if(keynum==1 || keynum==0){p1 = 0;}p2 = 1;p3 = 1;break;
   case 2: s10(); xuaze(shinum1); if(keynum==2 || keynum==0){p2 = 0;}p1 = 1;p3 = 1;break;
   case 3: s10(); xuaze(genum1);  if(keynum==3 || keynum==0){p3 = 0;}p1 = 1;p2 = 1;break;
   default:i=0;s10(); break;
}

}

void timer0_1init(){//定時器聲明
TMOD=0x11;//將定時器0,1都設置為模式1
TL0 = 0x18; //設置定時初值
TH0 = 0xFC; //設置定時初值
TR0=1;//開啟定時器0
TR1=1;//開啟定時器1
EA=1;//開總中斷
ET0=1;//開定時器0的中斷
}
/**********************數碼管顯示部分開始**************************/
void displaynums(){//將數字傳到數碼管上顯示
if (if0==0){//當if0==0時num1三個數碼管進行顯示
genum1=inum2%10;//個位
shinum1=inum2/10%10;//十位
bainum1=inum2/100;//百
}else{
bainum1=bainum11;
shinum1=shinum11;
genum1=genum11;
inum1=bainum11*100+shinum11*10+genum11; //將num1三個數碼管的值付給inum
inum2=inum1;
}
}
void s0(){pa = 1;pb = 1;pc = 1;pd = 1;pe = 1;pf = 1;pg = 0;}
void s1(){pb = 1;pc = 1;pa = 0;pg = 0;pd = 0;pe = 0;pf = 0;}
void s2(){pa = 1;pb = 1;pg = 1;pe = 1;pd = 1;pf = 0;pc = 0;}
void s3(){pa = 1;pb = 1;pg = 1;pc = 1;pd = 1;pf = 0;pe = 0;}
void s4(){pb = 1;pg = 1;pc = 1;pf = 1;pa = 0;pd = 0;pe = 0;}
void s5(){pa = 1;pg = 1;pc = 1;pd = 1;pf = 1;pe = 0;pb = 0;}
void s6(){pa = 1;pg = 1;pc = 1;pd = 1;pf = 1;pe = 1;pb = 0;}
void s7(){pa = 1;pb = 1;pc = 1;pf = 0;pe = 0;pd = 0;pg = 0;}
void s8(){pa = 1;pb = 1;pg = 1;pc = 1;pd = 1;pf = 1;pe = 1;}
void s9(){pa = 1;pb = 1;pg = 1;pc = 1;pd = 1;pf = 1;pe = 0;}
void s10(){pa =0;pb = 0;pc = 0;pf = 0;pe = 0;pd = 0;pg = 0;}
void xuaze(unsigned char j){
if(j == 0){s0();}
else if(j == 1){s1();}
else if(j == 2){s2();}
else if(j == 3){s3();}
else if(j == 4){s4();}
else if(j == 5){s5();}
else if(j == 6){s6();}
else if(j == 7){s7();}
else if(j == 8){s8();}
else if(j == 9){s9();}}
/**********************數碼管顯示部分結束**************************/
/**********************掉電存儲部分開始**************************/
//掉電存儲
//void Delay(BYTE n){
// WORD x;
// while (n--){x = 0;while (++x);}
//}
//關閉IAP
void IapIdle(){
   IAP_CONTR  = 0;                   //關閉IAP功能
   IAP_CMD  = 0;                      //清除命令寄存器
   IAP_TRIG  = 0;                   //清除觸發寄存器
   IAP_ADDRH  = 0x80;                //將地址設置到非IAP區域
   IAP_ADDRL  = 0;
}
//從ISP/IAP/EEPROM區域讀取一字節
BYTE IapReadByte(WORD addr){
   BYTE dat;                         //數據緩沖區
   IAP_CONTR = ENABLE_IAP;          //使能IAP
   IAP_CMD = CMD_READ;             //設置IAP命令
   IAP_ADDRL = addr;                //設置IAP低地址
   IAP_ADDRH = addr >> 8;          //設置IAP高地址
   IAP_TRIG = 0x5a;                //寫觸發命令(0x5a
   IAP_TRIG = 0xa5;                //寫觸發命令(0xa5
   _nop_();                         //等待ISP/IAP/EEPROM操作完
   dat = IAP_DATA;                   //讀ISP/IAP/EEPROM數據
   IapIdle();                      //關閉IAP功能
   return dat;                      //返回
}
//寫一字節數據到ISP/IAP/EEPROM區域
void IapProgramByte(WORD addr, BYTE dat){
   IAP_CONTR = ENABLE_IAP;          //使能IAP
   IAP_CMD = CMD_PROGRAM;          //設置IAP命令
   IAP_ADDRL = addr;                //設置IAP低地址
   IAP_ADDRH = addr >> 8;          //設置IAP高地址
   IAP_DATA = dat;                   //寫ISP/IAP/EEPROM數據
   IAP_TRIG = 0x5a;                //寫觸發命令(0x5a
   IAP_TRIG = 0xa5;                //寫觸發命令(0xa5
   _nop_();                         //等待ISP/IAP/EEPROM操作完
   IapIdle();
}
//扇區擦除
void IapEraseSector(WORD addr){
   IAP_CONTR = ENABLE_IAP;          //使能IAP
   IAP_CMD = CMD_ERASE;             //設置IAP命令
   IAP_ADDRL = addr;                //設置IAP低地址
   IAP_ADDRH = addr >> 8;          //設置IAP高地址
   IAP_TRIG = 0x5a;                //寫觸發命令(0x5a
   IAP_TRIG = 0xa5;                //寫觸發命令(0xa5
   _nop_();                         //等待ISP/IAP/EEPROM操作完
   IapIdle();
}
void saveeepro(){//掉電存儲
   inum11=inum1/100;//把int型的值拆分到char型
   inum12=inum1%100;
   inum21=inum2/100;
   inum22=inum2%100;
   IapEraseSector(0);
   IapProgramByte(1, inum11);//數值1
   IapProgramByte(2, inum12);
   IapProgramByte(3, inum21);
   IapProgramByte(4, inum22);
   IapProgramByte(5, if0);//倒計時的狀態
   IapProgramByte(6, if0s);//繼電器的狀態
   IapProgramByte(7, ss);//存分
}
/**********************掉電存儲部分結束**************************/
void keyflag(){//按鍵結束調用，按鍵的建議使用，這樣可以減小code，但是觸發的不建議
   if(kt0){//當標志位kt0=1的時候進行
   if(presstime>50){//當時間值大于一百的時候
kf0=1;//標志位kf0=1
kt0=0;//標志位kt0=0
   presstime=0;//時間清零，重新進行
}
   }
}

應用舉例延時接通.JPG (130.81 KB, 下載次數: 90)

數顯可編程延時接通或延時斷開模塊最新整理配套例程.rar

3.7 MB, 下載次數: 108, 下載積分: 黑幣 -5

數顯可編程延時接通或延時斷開模塊原理圖及PCB圖.rar

192.45 KB, 下載次數: 108, 下載積分: 黑幣 -5

作者: woshitomge 時間: 2020-11-24 14:10
這個項目真的很有用

作者: kenny136 時間: 2020-12-25 15:12
很實用的項目

歡迎光臨 (http://m.raoushi.com/bbs/)